Atec Agilent-8722ES Manuel d'utilisateur

5Agilent 8722ES with 2.4 mm test portsStandard, Options 400, 0121, 089, or any combina-tion of these options.Calibration kit: 85056A, 2.4-mm with slid

Agilent 8719ET and 8720ET with 3.5 mm test portsStandard or Option 004Calibration kit: 85052B 3.5-mm with sliding loads Cables: 85131F 3.5-mm flexible

Agilent 8722ET with 2.4 mm test portsStandard or Option 004Calibration kit: 85056A 2.4-mm with sliding loads Cables: 85133F 2.4-mm flexible cable set

16Agilent 8719ES, 8720ES, or 8722ES Option 012 Option 012 adds RF loops that provide direct accessto the A and B samplers in the port 1 and port 2rece

17Agilent 8719ES, 8720ES, and 8722ES Option 089Option 089 adds frequency offset mode, allowingthe receiver to be offset from the source frequency.This

18Agilent 8719ES, 8720ES, and 8722ESDescription CodeFrequency Range8719ES 0.05 to 13.51 GHz S8720ES 0.05 to 20.05 GHz S8722ES 0.05 to 40.05 GHz SAccur

19Agilent 8719ET, 8720ET, and 8722ETDescription CodeFrequencyRange8719ET 0.05 to 13.51 GHz S8720ET 0.05 to 20.05 GHz S8722ET 0.05 to 40.05 GHz SAccura

20Full frequency band sweep time (ms)1Number of PointsMeasurement 51 201 401 1601(Swept mode/Stepped mode)Single band sweep (10 to 12 GHz)Uncorrected

21Agilent 8719ES, 8720ES, and 8722ES Agilent 8719ET, 8720ET, and 8722ETTime-domain (Option 010)With the time-domain option, data from transmis-sion or

22GatingThe gating function can be used to selectivelyremove reflection or transmission time-domainresponses. In converting back to the frequencydomai

23Measurement capabilitiesNumber of display channelsFour display channels available.Number of measurement channels Two primary (independent) and two a

6Agilent 8719ES and 8720ES with 3.5 mm test portsStandard, Options 400, 0121, 089, or any combina-tion of these options.Calibration kit: 85052D, 3.5-m

24Internal source controlSweep limitsSet start/stop or center/span of the stimulusparameter (frequency, power, or time) directlythrough the source con

25TRL*/LRM* calibrationCompensates for directivity, reflection, and trans-mission frequency response, and crosstalk in boththe forward and reverse dir

26Display controlDisplay formatsSingle-channel, dual-channel overlay (both traceson one graticule), dual-channel split (each trace on separate graticu

27Limit linesDefine test limit lines that appear on the displayfor go/no go testing. Lines may be any combinationof horizontal, sloping lines, or disc

28GPIB (remote) programmingInterfaceGPIB interface operates to IEEE 488-1978 and IEC625 standards and IEEE 728-1982 recommendedpractices.AddressingThe

29Rear panel connectors (continued)• GPIB This connector allows communication with compatible devices including external controllers, printers, plotte

30Agilent 85071C materials measurement softwareDescriptionThe 85071C software uses broadband S-parametermeasurements to determine the electromagneticp

31A wide range of accessories support the Agilent8720E family of network analyzers, including cali-bration kits, verification kits, cables, and adapte

32Economy calibration kitsInclude the open circuit, short circuit, and fixedtermination standards but not sliding terminationsor gauges. Gauges can be

33Test port return cable specificationsConnector Ttpe Frequency Length2Return Insertion loss Stabillty1, 2±Phase (Test port to device) (GHz) cm (i

7Agilent 8722ES with 2.4 mm test portsStandard, Options 400, 0121, 089, or any combina-tion of these options.Calibration kit: 85056D, 2.4-mm with broa

34Test port adapter setsThe Agilent 85130 series test port adapter sets protect the test set port when connecting devicesto the test port. These adapt

Agilent Technologies’ Test and Measurement Support, Services, and AssistanceAgilent Technologies aims to maximize the value you receive, while minimiz

8Agilent 8719ES Option 400, 8720ES Option 400,and 8722ES Option 400 with 3.5 mm test portsusing TRLIncludes instruments with Options 0121and/or 089. C

9Agilent 8719ES, 8720ES, and 8722ES Option 007Agilent 8719ES, 8720ES, and 8722ES Option 085Includes instruments with Options 0121and/or 089.Option 007

10Agilent 8719ES or 8720ES with Option 007 or 085Calibration kit: 85052B 3.5-mm with sliding loadsCables: 85131F 3.5-mm flexible cable setIF bandwidth

11Agilent 8719ES or 8720ES with Option 007 or 085Calibration kit: 85052D 3.5-mm with fixed loadsCables: 85131F 3.5-mm flexible cable setIF bandwidth:

12Agilent 8722ES with Option 007 or 085Calibration kit: 85056A 2.4-mm with sliding loadsCables: 85133F 2.4-mm flexible cable setIF bandwidth: 10 HzAve

13Agilent 8722ES with Option 007 or 085Calibration kit: 85056D 2.4-mm with fixed loadsCables: 85133F 2.4-mm flexible cable setIF bandwidth: 10 HzAvera