Atec Agilent-81618A Manuel d'utilisateur Page 105
- Page / 112
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Additional Cleaning Information Cleaning Information
Agilent 81618A/9A and Agilent 81622B/3B/4B/6B/7B/8B User’s Guide, Second Edition 105
How to clean bare fiber ends
Bare fiber ends are often used for splices or, together with other
optical components, to create a parallel beam. The end of a fiber can
often be scratched. You make a new cleave. To do this:
1 Strip off the cladding.
2 Take a new soft tissue and moisten it with isopropyl alcohol.
3 Carefully clean the bare fiber with this tissue.
4 Make your cleave and immediately insert the fiber into your bare
fiber adapter in order to protect the surface from dirt.
How to clean large area lenses and mirrors
Some mirrors, as those from a monochromator, are very soft and
sensitive. Therefore, never touch them and do not use cleaning tools
such as compressed air or polymer film.
Some lenses have special coatings that are sensitive to solvents,
grease, liquid and mechanical abrasion. Take extra care when cleaning
lenses with these coatings.
Lens assemblies consisting of several lenses are not normally sealed.
Therefore, use as little liquid as possible, as it can get between the
lenses and in doing so can change the properties of projection.
Preferred Procedure Use the following procedure on most occasions.
1 Blow away any dust or dirt with compressed air.
Procedure for Stubborn Dirt Use this procedure when there is greasy dirt on the lens:
CAUTION Only use water if you are sure that there is no other way of cleaning
your optical device without causing corrosion or damage.
Only use water if you are sure that there is no other way of cleaning
your optical device without causing corrosion or damage. Do not use
hot water, as this may cause mechanical stress, which can damage
your optical device.
Ensure that your liquid soap has no abrasive properties or perfume in
it. You should also avoid normal washing up liquid, as it can cover
your device in an iridescent film after it has been air dried.
Some lenses and mirrors also have a special coating, which may be
sensitive to mechanical stress, or to fat and liquids. For this reason we
recommend you do not touch them.
- User’s Guide 1
- Second Edition: 2
- 81623-90B12 2
- Safety Considerations 3
- Initial Inspection 4
- Line Power Requirements 4
- Operating Environment 4
- Storage and Shipment 4
- Table of Contents 5
- Performance Tests 35 6
- Cleaning Information 87 6
- Table of Con tents 8
- What is an Optical Head? 11
- Analog Output 12
- Optical input 12
- Optical Head 13
- Accessories 15
- Modules and Options 17
- Table 1 Connector Adapters 19
- Specifications 21
- Definition of Terms 23
- Return loss 26
- Total uncert ai nty 26
- Wavelength range 26
- Optical Head Specifications 27
- <±0.04 dB ± 500 pW 29
- <±0.15 dB ± 500 pW 29
- *Attention 32
- Supplementary Performance 33
- Characteristics 33
- Performance Tests 35
- Equipment Required 37
- Test Record 38
- Test Failure 39
- Instrument Specification 39
- Functional Tests 40
- Accuracy Test 43
- Linearity Test 45
- Change Setup 50
- Calculation 51
- Example: Measurement Results 51
- Calculations 52
- Noise Test 54
- Return Loss Test 55
- (Optional Test) 57
- Polarization Ctrl 11896A 58
- DIN 4108 60
- (81113SC) 60
- 9.64 µW _______ 10.36 µW 65
- 9.72 µW _______ 10.28 µW 69
- 9.69 µW _______ 10.31 µW 81
- Calculation Sheets 85
- Your Entries 86
- Cleaning Information 87
- 81000xA Optical Head Adapters 89
- 8162xx Optical Power Heads 89
- Safety Precautions 90
- Why is it important to clean 90
- What do I need for proper 91
- Isopropyl alcohol 92
- Cotton swabs 92
- Soft tissues 93
- Pipe cleaner 93
- Compressed air 93
- Additional Cleaning Equipment 94
- Warm water and liquid soap 95
- Premoistened cleaning wipes 95
- Polymer film 95
- Infrared Sensor Card 95
- Preserving Connectors 96
- Cleaning Instrument Housings 96
- Which Cleaning Procedure 97
- How to clean lenses 100
- How to clean bare fiber ends 105
- Other Cleaning Hints 106
- *81623-90B12* 112
Produits connexes et manuels pour Équipement Atec Agilent-81618A
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.607 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels