Atec Teseq-ProfLine_2103 Manuel d'utilisateur télécharger pdf

Advanced Test Solutions for EMC

System

ProfLine 2103 is an accurate and ﬂ exible single phase system designed to measure harmonics and ﬂ icker

in accordance with IEC 61000-3-2 and IEC 61000-3-3, supporting testing on products consuming up to

11 Amps rms and 92 Amp peak @230 Vac. The system is supplied complete with a stable, accurate,

programmable 3 kVA power source. The ProfLine 2103 system is therefore ready to measure and record

any harmonics and ﬂ icker created by the EUT. A wide range of higher power AC source systems are

available from Teseq, please see ProfLine 2105, 2115, 2130, 2145 datasheets for suitable systems at

higher power or for 3-phase operation.

Measurements are made using precision, no burden, active hall-effect current transformers connected

via a dedicated cable to a multichannel fast Data Acquisition Card (DAQ) ﬁ tted inside a PC. One voltage

and three current measuring channels are used to make simultaneous measurement of both current

and voltage. Calculations are made using dedicated Teseq software (WIN 2100) to determine harmonics

(classes A-D), inter-harmonics, ﬂ icker, dc, dt, dmax, Pst, Plt, inrush current and 24 x dmax.

Impedance

Measurement of ﬂ icker requires a ﬁ xed, stable source impedance as speciﬁ ed in IEC 61000-3-3 (0.24 Ω

+ j0.15 Ω in the line and 0.16 Ω + j0.1 Ω in the neutral). The precision power source (NSG 1007-3) supplied

as part of the system is able to accurately simulate this impedance by careful control of the relation-

ship between voltage and current. This eliminates the need for a costly physical impedance. However,

hardware lumped impedances are available from Teseq, see options list.

Power quality measurement

The power source (NSG 1007-3) supplied as part of the ProfLine 2103 system is able to perform tests in

conformance to a number of immunity standards. IEC 61000-4-13 (immunity to harmonics and interhar-

monics), IEC 61000-4-14 (voltage ﬂ uctuations), IEC 61000-4-17 (ripple on DC) and IEC 61000-4-28 (variation

of power frequency). Additionally it can also perform pre-compliance testing to IEC 61000-4-29 (voltage

dips, interrupts and variations on DC supply) and IEC 61000-4-11. With the addition of further options

IEC 61000-4-8 (power frequency magnetics) and fully compliant IEC 61000-4-11 (voltage dips, interrupts

and variation on AC supply) can be implemented.

3 KVA 1-PHASE HARMONICS AND FLICKER

MEASURING SYSTEM

PROFLINE 2103

Low cost system for small DUTs

Complete test system including

clean power source

Simulated flicker impedance,

no need for expensive physical

impedance

1 2 3

MEASURING SYSTEM 2

Résumé du contenu

Page 1

Advanced Test Solutions for EMCSystemProfLine 2103 is an accurate and ﬂ exible single phase system designed to measure harmonics and ﬂ icker in accord

Page 2 - MEASURING SYSTEM

Advanced Test Solutions for EMCMains supply options ProfLine 2103-240System contents NSG 1007-3-240 Power source CCN 1000-1 1-phase coupling

Page 3

Advanced Test Solutions for EMCDAQ card and cableInterface PCISize Standard heightResolution 16 bitSpeed 250 kSamples/sCable length PC to

Commentaires sur ces manuels

Pas de commentaire

Atec Teseq-ProfLine_2103 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Atec Teseq-ProfLine_2103. Atec Teseq-ProfLine_2103 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Atec Teseq-ProfLine_2103