Agilent PSA Series Spectrum Analyzers Data SheetThe Agilent PSA Series offers high-performance spectrum analysis, up to 50 GHz, with powerful one-butt
10Amplitude Specifi cations (continued)Display rangeLog scale 0.1 to 1 dB/division in 0.1 dB steps 1 to 20 dB/division in 1 dB steps (10 display div
11Amplitude Specifi cations (continued)Input voltage standing wave ratio (VSWR) (≥ 8 dB input attenuation)50 MHz to 3 GHz < 1.2:1 nominal3 GHz to 18
12Amplitude Specifi cations (continued)Second harmonic distortion (SHI)E4443A/E4445A/E4440A Distortion (dBc) SHI (dBm)10 MHz to 460 MHz (–40 dBm mixer
13Amplitude Specifi cations (continued)Nominal Dymamic RangeBand 0DANL and distortion relative to mixer level (dB)–60–70–80–90–100–110–120–130Mixer Lev
14Residual responsesInput terminated and 0 dB attenuation 200 kHz to 6.6 GHz –100 dBm6.6 GHz to 26.8 GHz –100 dBm nominal26.8 GHz to 50 GHz –90 dBm n
15Other Specifi cationsOption AYZ, external mixingFrequency range 18 to 325 GHz (to 110 GHz with the Agilent unpreselected mixer)LO outputFrequency ran
16Channel powerAmplitude accuracy, W-CDMA or IS95 (20 to 30 °C, mixer level < –20 dBm)±0.68 dB ( ±0.18 dB typical)Occupied bandwidthFrequency accur
17Power Suite Measurement Specifi cations (continued)Spurious emissionW-CDMA (1980 MHz region, 1.2 MHz RBW) Table driven spurious signals; search acros
18General Specifi cationsTemperature rangeOperating 0 °C to +55 °CStorage –40 °C to +70 °CEMI compatibilityRadiated and conducted emission is in comp
19Inputs and OutputsFront panelRF inputConnector E4443A/E4445A Type-N female, 50 Ω E4440A Type-N female, 50 Ω Option E4440A-BAB APC 3.5 ma
2Table of ContentsDefi nitions and Conditions . . . . . . 3Frequency Specifi cations . . . . . . . 4 Frequency range . . . . . . . . . . . . . . . .
20Rear panel (continued)Monitor outputConnector VGA compatible, 15-pin mini D-SUBFormat VGA (31.5 kHz horizontal, 60 Hz vertical sync rates, non-inter
21PSA Series Ordering InformationFor further information, refer to PSA Confi guration Guide, 5989-2773ENPSA Series spectrum analyzerE4443A 3 Hz to 6.
22PSA Series Ordering Information (continued)For further information, refer to PSA Confi guration Guide, 5989-2773ENHardwareE444xA-1DS RF internal prea
23Related LiteraturePublication Title Publication Type Publication NumberPSA in generalSelecting the Right Signal Analyzer for Your NeedsSelection Gui
Remove all doubtOur repair and calibration services will get your equipment back to you, performing like new, when prom-ised. You will get full value
3Defi nitions and ConditionsSpecifications describe the perfor-mance of parameters covered by the product warranty and apply over 0 to 55 °C unless oth
4Frequency Specifi cationsFrequency rangeE4443A (DC coupled) 3 Hz to 6.7 GHz (AC coupled) 20 MHz to 6.7 GHzE4445A (DC coupled) 3 Hz to 13.2 GHz (AC cou
5Frequency Specifi cations (continued)Sweep time and triggeringRange Span = 0 Hz 1 µs to 6000 sSpan ≥ 10 Hz 1 ms to 2000 sAccuracy Span ≥ 10 Hz, sweep
6Frequency Specifi cations (continued)Analysis bandwidth 1Maximum bandwidthwith Option 140 240 MHzwith Option 122 280 MHzwith Option B7J 10 MHz 1. Ana
7Amplitude Specifi cationsAmplitude rangeMeasurement range Displayed average noise level (DANL) to maximum safe input levelInput attenuator range (3 Hz
8Amplitude Specifi cations (continued)Displayed average noise level (DANL)(Input terminated, sample or average detector, averaging type = Log, 20 to 30
9Amplitude Specifi cations (continued)Displayed average noise level (DANL) (Input terminated, sample or average detector, averaging type = Log, 20 to 3
Commentaires sur ces manuels